|
If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
Datasheet File OCR Text: |
SPEC NO : SPECIFICATION CUSTOMER PRODUCT MODEL NO PREPARED APPROVED SAW FILTER HDBF43A1DC SIP5Dc CHECKED D A T E 2007-8-21 CUSTOMER RECEIVED: CHECKED APPROVED DATE Shoulder Electronics Limited www.shoulder.cn Tel:0755-82916880 Fax:0755-82916881 E-mail:info@shoulder.cn Page 1 of 8 SAW FILTER HDBF43A1DC SIP5Dc History Record Date Spec. No. Part No. Customer No. Modify Content Remark www.shoulder.cn Tel:0755-82916880 Fax:0755-82916881 E-mail:info@shoulder.cn Page 2 of 8 SAW FILTER 1.SCOPE HDBF43A1DC SIP5Dc SHOULDER's SAW filter series have broad line up products meeting all broadcast standard including NTSC,PAL and SECAM systems. These filters are composed of two interdigital transducers on a single-crystal. piezoelectrical chip. they are used in electronic equipments such as TV and so on. 2.Construction 2.1 Dimension and materials Manufacturer's name : SHOULDER ELECTRONICS Co. LTD(CHINA) Type : BF43A1Dc Pin configuration 1.input 2.input-ground 3.Chip carrier-ground 4.Output 5.Output YY:year WW:week www.shoulder.cn Tel:0755-82916880 Fax:0755-82916881 E-mail:info@shoulder.cn Page 3 of 8 SAW FILTER 2.2. Circuit construction, measurement circuit HDBF43A1DC SIP5Dc 3.Characteristics Items Standard atmospheric conditions Conditions Unless otherwise specified , the standard rang of atmospheric conditions for making measurements and tests is as follows; Ambient temperature : 15 to 35 Relative humidity : 25% to 85% Air pressure : 86kPa to 106kPa Operating temperature rang is the rang of ambient temperatures in which the filter can be operated continuously. -20 ~ +60 Storage temperature rang is the rang of ambient temperatures at which the filter can be stored without damage. Conditions are as specified elsewhere in these specifications. -40 ~ +70 +25 Specifications Operating temperature rang There shall be no damage. Storage temperature rang Reference temperature www.shoulder.cn Tel:0755-82916880 Fax:0755-82916881 E-mail:info@shoulder.cn Page 4 of 8 SAW FILTER 3.1 Maximum Rating DC voltage AC voltage VDC Vpp 12 10 V V HDBF43A1DC SIP5Dc Between any terminals Between any terminals 3.2 Electrical Characteristics Source impedance Zs=50 Load impedance ZL=2k//3pF Item Freq Center frequency Fo Insertion attenuation 43.81MHz Reference level B3dB Pass bandwidth B30dB 40.71MHz Relative attenuation 46.91MHz 35.06~39.06MHz 39.06~39.76MHz Sidelobe 47.86~49.66MHz 49.66~55.06MHz Group delay ripple(p-p) 40.81~46.81MHz Temperature coefficient min 13.2 36.0 34.0 34.0 36.0 - typ 43.75 15.2 6.2 7.6 3.0 2.2 45.0 42.0 42.0 46.0 40 -72 TA=25 max 17.2 - MHz dB MHz MHz dB dB dB dB dB dB ns ppm/k - 3.3 Environmental Performance Characteristics Item Condition High The specimen shall be store at a temperature of temperature 802 for 964h. Then it shall be subjected to standard atmospheric conditions for 1h, after which measurement shall be made within 1h. Low The specimen shall be store at a temperature of temperature -203 for 964h. Then it shall be subjected to standard atmospheric conditions for 1h, after which measurement shall be made within 1h. Humidity The specimen shall be store at a temperature of 402 with relative humidity of 90% to 96% for 964h. Then it shall be subjected to standard atmospheric conditions for 1h, after which measurement shall be made within 1h. Thermal The specimen shall be subjected to 8 continuous shock cycles each as shown below. Then it shall be www.shoulder.cn Tel:0755-82916880 Fax:0755-82916881 E-mail:info@shoulder.cn Specifications Mechanical characteristics and specifications in electrical characteristics shall be satisfied. There shall be no excessive change in appearance. Page 5 of 8 SAW FILTER HDBF43A1DC subjected to standard atmospheric conditions for 1h, after which measurement shall be made within 1h. Temperature Duration 1 +25 =>-40 0.5h 2 -40 4h 3 -40 =>+85 2h 4 +85 4h 5 +85 =>+25 0.5h 6 +25 1h Reflow soldering method Peak: 255 5 , 220 5 , 40s At electrode temperature of the specimen. SIP5Dc Resistance to Soldering heat Solder ability The specimen shall be passed through the reflow furnace with the condition shown in the above profile for 1 time. The specimen shall be stored at standard atmospheric conditions for 1h, after which the measurement shall be made. Test board shall be 1.6 mm thick. Base material shall be glass fabric base epoxy resin. Immerse the pins melt solder at 260+5/-0 More then 95% of for 5 sec. total area of the pins should be covered with solder www.shoulder.cn Tel:0755-82916880 Fax:0755-82916881 E-mail:info@shoulder.cn Page 6 of 8 SAW FILTER 3.4 Mechanical Test Items Conditions Vibration 600-3300rpm amplitude 1.5mm 3 directions 2 H each Drop On maple plate from 1 m high 3 times Lead pull Lead bend Pull with 1 kg force for 30 seconds 90o bending with 500g weigh 2 times HDBF43A1DC SIP5Dc Specifications There shall be no damage. 3.5 Voltage Discharge Test Item Condition Surge Between any two electrode Specifications There shall be no damage www.shoulder.cn Tel:0755-82916880 Fax:0755-82916881 E-mail:info@shoulder.cn Page 7 of 8 SAW FILTER 3.6 Frequency response HDBF43A1DC SIP5Dc www.shoulder.cn Tel:0755-82916880 Fax:0755-82916881 E-mail:info@shoulder.cn Page 8 of 8 |
Price & Availability of HDBF43A1DC |
|
|
All Rights Reserved © IC-ON-LINE 2003 - 2022 |
[Add Bookmark] [Contact Us] [Link exchange] [Privacy policy] |
Mirror Sites : [www.datasheet.hk]
[www.maxim4u.com] [www.ic-on-line.cn]
[www.ic-on-line.com] [www.ic-on-line.net]
[www.alldatasheet.com.cn]
[www.gdcy.com]
[www.gdcy.net] |